支持 TouchLink Pro 触摸屏和 eBUS® 按键面板 视音频局域网端口可使视音频设备与企业网络 分离 支持行业安全标准的通信协议 支持 LinkLicense 6 个支持软件握手的双向 RS-232 串行端口
Extron IPCP Pro 555 是一款通用的高性能控制处理器，带一个视音频局域网端口。它采用安全标准和双千兆以太网端口，确保了在当今网络构架上与多个 TouchLink® Pro 触摸屏相兼容。其中的视音频局域网端口专门用来控制本地视音频设备，可避免外部干扰或入侵。IPCP Pro 555 可与 Extron LinkLicense® 配合使用，能进一步增强 Extron Pro 系列控制系统的处理能力。在需要隔离控制的视音频系统中，IPCP Pro 555 是控制多个设备和多种控制信号类型的理想之选。
特性
支持 TouchLink Pro 触摸屏和 eBUS® 按键面板
视音频局域网端口可使视音频设备与企业网络 分离
支持行业安全标准的通信协议
支持 LinkLicense
6 个支持软件握手的双向 RS-232 串行端口
2 个支持硬件和软件握手的双向RS-232/RS-422/RS-485 串行端口
8 个红外/串行端口，用于外部设备的单向控制
4 个多功能输入/输出端口
8 个继电器，用于控制房间功能
4 路可独立开关的 12 VDC 电源输出
每个以太网端口都具有以太网监视和控制功能
中央部署 - 使用主控制处理器来部署所有的系统文件、配置和程序 — 通过上传所有项目文件至主控制处理器来快速部署控制系统。主控制处理器会自动地将文件传输至系统内的其它联网触摸屏、控制处理器和按键面板。
用于视音频局域网的 DHCP 服务器
支持常见的 BMS（建筑管理系统）协议，如 BACnet、KNX 和 DALI
| IPCP Pro 555 | |
| Memory | |
|---|---|
| | 512 MB |
| | 4.5 GB |
| Software and control options | |
| | Extron Global Configurator® Plus and Professional for Windows®, Global Scripter® |
| | GlobalViewer®, Extron Control for iPad and Web, TouchLink® Pro touchpanels, or eBUS® button panels |
| Ethernet control | |
| | 2: 1 LAN, 1 AV LAN |
| | 2 female RJ-45 connectors |
| | 10/100/1000Base-T, half/full duplex with autodetect |
| | DHCP, DNS, HTTP, HTTPS, ICMP, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UDP/IP |
| | |
| | Link speed and duplex level = autodetected IP address = 192.168.253.250 Subnet mask = 255.255.255.0 Gateway = 0.0.0.0 DHCP = off DNS: 127.0.0.1 |
| | Link speed and duplex level = autodetected DHCP server = disabled Subnet mask = 255.255.255.0 Gateway = 0.0.0.0 |
| | IP address = 192.168.254.250 DNS = 127.0.0.1 |
| | IP address = 192.168.254.1 DNS = 192.168.254.1 Dynamic leased IP address pool = 192.168.254.100 - 192.168.254.149 Maximum lease count = 50 Lease time = 24 hours |
| Serial control | |
| | 2 bidirectional RS-232, RS-422, RS-485 (ports 7 and 8) 6 bidirectional RS-232 (ports 1 through 6) |
| | (2) 3.5 mm captive screw connectors, 5 pole (6) 3.5 mm captive screw connectors, 3 pole |
| | 300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits; no parity (default), even, or odd parity |
| NOTE The 5-pole ports support both hardware and software flow control.The 3-pole ports support software flow control.The default for both types of ports is no flow control. | |
| | |
| Serial, 5-pole captive screw | |
| | Pin 1 = Tx, 2 = Rx, 3 = Gnd, 4 = RTS, 5 = CTS |
| | Pin 1 = Tx-, 2 = Rx-, 3 = Gnd, 4 = Tx+, 5 = Rx+ |
| | Pins 1 and 2 (tied together) = data-, 3 = Gnd, 4 and 5 (tied together) = data+ |
| | Pin 1 = Tx, 2 = Rx, 3 = Gnd |
| Flex I/O control | |
| | 4 analog input or digital input/output (configurable) |
| | (1) 3.5 mm captive screw connector, 5 pole |
| | |
| | 0 to 24 VDC, clamped at +30 VDC |
| | 29k ohms |
| | 1k ohms to +5 VDC |
| | Programmable range: 100 mV to 24 VDC, default = 2.4 VDC |
| | Programmable range: 100 mV to 24 VDC, default = 0.8 VDC |
| | 250 mA sink from 24 VDC max. |
| | 12 bit A/D, 0 to 24 VDC |
| | 1, 2, 3, 4 = flex I/Os 1, 2, 3, 4; 5 = Gnd |
| IR/serial control | |
| | 8 programmable: unidirectional RS-232 (±5 V), or TTL level (0 to 5 V) infrared (carrier and non-carrier) up to 300 kHz |
| | (4) 3.5 mm captive screw connectors, 4-pole |
| | 300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits; no parity (default), even, or odd parity |
| | For each port, pin 1 = signal, 2 = Gnd |
| | 30 kHz to 300 kHz |
| | 30 kHz to 300 kHz |
| | 2" (5.1 cm) to 12" (30.5 cm) from the front panel |
| Relay control | |
| | 8 normally open relays |
| | (4) 3.5 mm captive screw connectors, 4 pole |
| | 24 VDC, 1 A |
| eBUS control | |
| | (1) 3.5 mm captive screw connector, 5 pole (uses 4 poles) |
| | +V = +12 VDC; +S = + signal; -S = - signal; G = ground |
| | Extron STP20-2/1000 or STP20-2P/1000 cable |
| | 1000 feet (305 meters) sum total for the eBUS system, regardless of topology. Power injection may be required depending on system cabling topology and primary power supply wattage. See the eBUS Technology Reference Guide for details. |
| | 12 watts |
| Switched DC power output | |
| | 4 switched 12 VDC outputs |
| | (4) 3.5 mm captive screw connectors, 2 pole |
| | Maximum 40 watts total |
| | |
| | 0.1 watt to 40 watts |
| General | |
| | Internal Input: 100-240 VAC, 50-60 Hz |
| | 65.2 watts |
| | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| | Convection, no vents |
| | 45.8 BTU/hr |
| | |
| | Yes, with optional 1U rack shelf |
| | Metal |
| | 1.7" H x 8.7" W x 10.5" D (1U high, half rack wide) (4.3 cm H x 22.1 cm W x 26.7 cm D) (Depth excludes connectors.) |
| | 2.5 lbs (1.1 kg) |
| | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| | CE, c-UL, UL UL Listed for use in plenum air handling spaces |
| | CE, C-Tick, FCC Class A, ICES, VCCI |
| | Complies with the appropriate requirements of RoHS, WEEE |
| | 3 years parts and labor |
| | 7 years parts and labor |
| NOTE All nominal levels are at ±10%. | |
| NOTE Specifications are subject to change without notice. | |
